Showing posts with label vintage. Show all posts
Showing posts with label vintage. Show all posts

DIY: Faux Bamboo Moulding



I recently changed out the base cabinets of my office from IKEA Malms to new IKEA kitchen Sektion cabinets.  They are much deeper and offer a ton of flexibility with organization.  (I can do an entire post on them!) I also added a few homemade whiteboards using simple stock moulding for frames.

Everything is very basic and flat, so I spun on some ideas to hack them into something a bit more fabulous.  I have long loved the look of faux bamboo on furniture, so I did a bit of research and found a few sites that sell the actual moulding like this site here.  It comes in 34" lengths and runs about $8.50 or $12.50 per piece for the 3/4" and 1 1/8" respectively.  I needed over 60 feet for my project and many were lengths much larger than 34".  I decided to figure out how to make it myself- and I did it for under $30 for the entire project!  It was a bit of trial and error, but I think I got it down for you.  It also goes pretty quickly in the "making" department.  I made the moulding for the above cabinet in under 30 minutes, the more you do the faster you get.  The remaining workload... the painting, cutting and applying... are all things you'd have to do with the store bought variety.

You will need:

-half round molding (Any size/ length you desire... price shop if you can.  I saved $0.49 per foot by checking around with different lumber yards- that adds up quick!)
-wood putty (I liked Zar's- see pic below)
-stiff piece of plastic- I used an old rewards card from my wallet
-scissors
-small brush
-bowl of water
-extra fine sandpaper
-saw to cut the moulding ( I recommend doing all your cuts before starting the tutorial.  The small bumps can throw off your 45 degree cuts.)

First off lets talk about wood putty... I found this one by Zar to work great.
I has a good consistency, not too stiff and not too runny.  


I did try some tubes with epic failure.  
It fell right off because there isn't enough pressure applied to get it to bond and this putty was very dry and gritty..
It's a big NO.
I did consider putting the Zar putty into a cake decorating tube, but you really need to make sure the putty is sticking to the wood.  The only sure way is by rubbing or wiping it on to the wood by hand.

1) Begin by gathering all your moulding and making all cuts.  It's so much easier to do this before the bamboo relief is on!   Be sure to mark the backsides if necessary so you know how to reassemble.
Next want to mark where you want to 
"add" bamboo.  I did mine every 5 inches because of drawer heights, but this is totally up to you.

2) Make a template.  Find an old credit or a store rewards card and cut two notches out.
These are going to make your bamboo lines...

3) Smear the putty onto the wood moulding by using your finger or a butter knife...
 It should look something like this:
When you start, only do one or two at a time since the putty dries quickly.  Once you master the technique you can do as many as you feel comfortable doing.  
If you find the putty getting too stiff or dry before you are able to manipulate it, try misting it with a little water.  You will also want to keep the lid of your container of putty closed when not in use.


4) Swipe that card! Starting from one side press the plastic card into the wood and drag it over to the other side creating two channels.  I liked to swipe towards me when working.  You can try angling the card down when you get toward the end, and be sure to go slowly.
Wipe the excess off the card.

 You should now have something like this:
If you totally blow it the first few times don't give up. Just wipe it off and try again.  It takes a bit of practice.  If you finding that you are missing the tops or getting random bumps try cutting the template a little smaller or try adding more putty.

5) Now get your water and brush.  Its time to clean up...

 Dip your brush in the water and run it along the edges and down the center.  This also helps create a nice smooth bond to the wood.
 You can also wipe off excess and shape the edges with the brush.  Don't go too crazy.
You can sand off small bumps and excess when it dries.  
6) Now let it dry for a few hours.  It will get very hard and should bond to the wood since the putty is made from pulverized wood and glue.  I was afraid this might chip, but I dropped a few pieces and they held up fine!
 I made a cabinet's worth of 1 1/8" moulding as well as several strips of the 3/4" moulding (painted white below)...

7) Once it is dry lightly sand with a fine grit sand paper (180-220 grit is good).  Be sure to sand the back sides too if any putty got on them.  (I used a 100 grit for areas that had a lot of excess.) 

You can prime and paint them, and then apply them to your project.

I will be adding the 3/4" strips around all four of my white boards to dress them up:
And  the 1 1/8" strips are going around the two base cabinets at my desk.
I used a nail gun to apply, but you can also use a strong adhesive glue.
 Be sure to putty the seams and nail holes, sand and touch up the paint.
 Add your hardware and your done.
This can be used on picture frames, mirror, table edges, doors, walls... 
the applications are endless!  
I will be bambooing the crap out of my office over the next week and I'll be sure to post better "daytime" photos.  (sorry for the sucky night ones)
Happy bambooing!


If you like vintage couture don't miss this today...

There is an AMAZING vintage couture auction happening a mile from my house today at Kaminski Auctions starting @11:00 (and I can't go because I have a birthday party to attend!) You have to check this out. Phone bidding is available. There are so many goodies! Tons of clothing, vintage jewelery and bags. Ugh, heaven!

More Emilio Pucci than I can shake a stick at, like I'd actually shake a stick at it. I'd be wearing it!
 And so many cute things.
Someone go or buy something and report back.
There are 11 pages of stuff. Had to stop looking because it was killing me.

I almost peed my pants...

Hi everyone! I'm ruh-EEEaly excited about this.  Remember this sculpture I found and posted about  a while ago ( I can't find the post because I suck at labeling). ..
 Well I considered selling it on the shop, so I took it down and flipped it over to see who made it and do some research.
I found a small round sticker on the back the same as the top one below, so enter Google.
I discover it was made by this dude, Mark Weinstein back in the 70's...
They had a downloadable brochure on the site from 1974 that showcased his collection...
Anybody else have anything that looks remotely familiar to this stuff? Do share!



And HELLO! There is my piece turned sideways above.
Hi Topaz, nice to meet you. Lovely name you have there.

 He does some amazing pieces, and was considered a Brutalist. He started off working at his father's scrap yard out of high school and found tons of inspiration there. He learned welding and started making sculptures and started his company Marc Creates in 1967.
It is now run mostly by his two sons, and they are remaking his original pieces. The new pieces have the marking below the sticker above and the bigger ones retail around $1000, and his original works have the sticker.  I found some of his original collection on 1st Dibs...


I know these prices are way inflated and all, but I did the happy dance and had an" almost peed my pants moment" regardless. I 'd hug the thing, but I'd cut the crap out myself doing so.
I think I'm keeping this one. Unless of course some rich Mark Weinstein collector would like to add "Topaz" to their collection for a fair price. call me ;) 

I'm off to act like an idiot & feel all smug and proud of myself for buying crap.
xo

A Very Brady Outing- A Boston Must Do

My family and I hit the SOWA Vintage Market this morning in Boston. Talk about my "happy place"... I love me some vintage and did they ever have it! We picked up a few items.  The boys got some signage. (My husband was a sign maker so he loves collecting it.) We loved the orange 26 (the other side reads 38) from a gas station, and my oldest wanted the danger sign... he is just a little obsessed with cars. Not quite sure yet where any of its going yet...
Mama got some vintage Trifari bling...
My littlest wanted this chair...
He liked that it was small and swiveled, and I was quite impressed with his taste for a three year old, but he lost the argument. Now if he mentioned recovering it in some Trina Turk, I would have considered him highly gifted and bought it for him on the spot.
It was quite cute, but it stayed at the market.

There was so much great stuff to see...

If you are in the neighborhood it is open until 5:00 today.
The orange sign below almost made it home with us for the kitchen...

I really liked the lamp and wooden map...

and this wall sculpture...

They have a large section of painted repurposed furniture...

Oh, and check out this Lucite bench... $100 and its yours.

Don't forget the vintage clothing and baubles (MY fave).

If you are in the Boston area you need to stop in.  Today was a smaller venue, as will be Sunday
April 3rd, but come mid-May to October 31st it will be going full force and will be open Sundays 10-4.
Be sure to say "hello" to my new friends Stephanie Pernice and John Warren, creators of this wonder happening. The Herricks will definitely be back!

LinkWithin

Related Posts with Thumbnails